Exactly How to Replace a Tub in Your Bathroom
Exactly How to Replace a Tub in Your Bathroom
Blog Article
What're your concepts on How to Install a Bathtub?
Installing a tub isn't exactly brain surgery, yet it does need solid plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently available, the task can move speedily; if you have to open up a wall to get rid of the old tub and also position the brand-new bathtub, the job is a lot harder. In either situation, the task is within a home handyman's abilities, although you will require a helper to leave the old bathtub and embeded in the new one. Make certain you have qualified on your own for the job as well as are comfortable attempting it. As opposed to hiring a service provider to take over a halfway-completed job, it is far better to consider utilizing one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This article will certainly aid you install a new bath tub in your bathroom if you have currently bought a new bathtub and also don't need to transform the setup of your previous supply of water pipelines.
Your devices and material list need to comprise the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted access that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin making sure that the washers are in area in between the faucet as well as the sink. Secure the faucet in position with the maker offered backnut. Once the faucet is firmly in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap connectors. The previous kind ought to be attached to the faucet ends initially, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Using both wood boards under its feet, place the bathtub in the required setting. The wooden boards are valuable in evenly spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four tiny points.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bath tub until the level checks out level.
To set up taps, fit all-time low of the furthest adaptable faucet connector to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Turn on the water as well as check all joints as well as new pipework for leakages and tighten them if needed. Fill the tub as well as likewise check the overflow electrical outlet and the regular outlet for leaks.
Lastly, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the bathtub needs to wait until the bath tub has been made use of a minimum of when as this will resolve it into its last setting.
Planning for the Setup
To start with, the supporting structure supplied with the bathroom ought to be fitted (if called for) according to the producer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the tap includes a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps device to prevent stress on the bath tub.
Fit the versatile faucet connectors to the bottom of the two faucets making use of 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its last setting.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall between the bath and the tiling, leading to complications with dampness and possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components as well as fittings. They are offered in tubes and cartridges, and are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the tub with water before sealing, to allow for the activity experienced when the bathtub remains in use. The sealant can crack rather very early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious person who reads about Installing A Bathtub, I was thinking sharing that post was beneficial. Remember to take the time to share this write-up if you enjoyed it. Thanks for taking the time to read it.
Apply Now Report this page